ABRITES Commander for VAG

`

ABRITES Commander for VAG is a Windows PC based diagnostic software for the vehicles from VAG. With the help of this tool you can perform operations with vehicles from the VAG group, which are in most cases unsupported from the producer diagnostic testers. The ABRITES Commander for VAG provides you also a full diagnostic capabilities for VAG-vehicles.

Highlights:

• Extracting security access codes (PIN) by OBDII
• Programming keys by OBDII. Preparation of dealer's keys.
• Mileage recalibration by OBDII
• Clearing crash data DTCs by OBDII
• Read/Program flash memory of engine control units by OBDII. Options for resetting the number of flashing attempts.
• Exchange speed limit of MMI-TV system
• Coding calculator - supported short/long coding
• Synchronization/Adaptation KESSY and ELV

Standard diagnostic functions:

• Connect to the device using KWP2000 over TP2.0, KWP2000 over TP1.6, UDS over ISO transport protocol (CAN), KWP1281 or KWP2000 over K-Line
• For all electronic control units reading identification data
• For all electronic control units read error (DTCs)
• For all electronic control units clear error (DTCs)
• Output tests
• Control unit coding
• Scan all units
• Broadcast requests
• Measured values
• Adaptation

Special functions:

• Instrument CAN
  - Mileage recalibration by OBDII - VW Golf 6, VW Multivan 2009+, VW EOS 2009+, VW Caddy 2009+, VW Scirocco, VW Polo 2009+, VW Bora 2010+, VW Jetta 2010+, VW Passat CC, VW Amarok, Skoda Octavia II 2009+, Skoda Superb 2009+, Skoda Fabia 2009+, Skoda Yeti 2009+, Seat Leon 2009+, Seat Altea 2009+, Seat Exeo 2009+, Seat Ibiza 2009+, ...
  - Added support for VDO Instrument Cluster 2006+
  - Read/Program memory of instrument cluster immobilizer
  - Reading security access code of the IMMOBILIZER
  - Reading security code (PIN) and component protection by OBDII - VW CRAFTER
  - Read/Write immobilizer data in VDO dashboards with NEC microcontroller (2009+) by OBDII
  - Read/Write immobilizer related data
  
• EZS - Kessy (Q7/A6/Allroad)
  - With this function you can prepare dealer key/learn dealer key
  - Read/Write eeprom from EZS - Kessy (Q7/A6/Allroad)
• Instrument K-Line
  - With this function you can establish disgnostic session with the Instrument cluster via K-Line (KWP1281 or KWP2000)
  - You can Read/Change odometer value
  - Read PIN code
  - Read/Write eeprom
  - Read ROM/Flash from the Instrument cluster
  - Automatic removing of "DEF error" for Audi A4 instrument cluster BOSCH RB8
  
• Engine Control Unit
  - Read EDC17/MED17 flash memory
  - Read/Write of flash memory (EDC15, EDC16 all types Read/Write Flashmemory via OBDII (K and CAN). Calculation of
  checksums while programming, ME7.1.1, MED9.x, ME7.5)
  - Read/Write flash counters (EDC16)
  - Read/Write eeprom (VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8.)
  - Extracting Security access code / PIN (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, EDC17, MED9.x, Simos PPD)
  - Extracting Component security bytes (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, MED17.5.1, MED 9.x, Simos PPD)
  - Enable/Disable immobilizer (EDC15, ME7.x, EDC16)
  - Mileage recaslibration (EDC15, EDC16)
• Component Protection Manager
  - Component Protection Manager - adaptation of spare part (used electronic control units) and programming component protection of Audi A6/Q7/Allroad/A4/A5/Q5
• ECU adaptation by OBDII
  - ECU adaptation by OBDII - EDC16, EDC17, MED17, MED9, Simos petrol, SIMOS PPD Diesel, ME7.5.20, ME 7.5.30
  
• BCM2 - Audi A4/A5/Q5 2007+ key programming
  - The special function makes possible to learn keys for A4/A5/Q5 2007+ vehicles with the BCM2 immobilizer
• Steering Lock adaptation
  - The window “Steering lock adaptation” can be used for adaptation of steering lock control module to the VW Touareg/VWPhaeton/Porsche Cayenne/Bentley Continental/Audi A8. This adaptation can be by CAN TP2.0 or K-KWP2000
• TV activation ED1/ED2
  - Using this special function you can change speed limit of MMI compatible vehicles to change speed where TV becomes OFF
• Key programming/adaptation
  - Programming keys by OBDII (VAG with 16 bytes Component Security) - VW Crafter, Audi R8, VW Golf 6, VW Multivan 2009+, VW EOS 2009+, VW Caddy 2009+, VW Scirocco, VW Polo 2009+, VW Bora 2010+, VW Jetta 2010+, Skoda Octavia II 2009+, Skoda Superb 2009+, Skoda Fabia 2009+, Skoda Yeti 2009+, Seat Leon 2009+, Seat Altea 2009+, Seat Exeo 2009+, Seat Ibiza 2009+, ... Free for owners of AN024+AN026
  - UNLIMITED production of TP22/TP23/TP24/TP25 transponders from a Megamos 48. Free for all owners of AN024, ZN001
  - No more precoded transponders (TA2/TA3/TA4/TA5) are used for the key-learning. Instead any Megamos 48 Crypto transponder can be used. Free for all owners of ZN001
  - Extracting of the 7th byte Component Security from a working key of the car (Megamos, Hitag2). Free for all owners of AN024, ZN001
  - LAMBORGHINI GALLARDO
  - With this function you can learn key/transponder to the vehicle
• Dump tool
  - With this function you can calculate security access codes, change odometer and so on from EEPROM dump from the correcponding unit
• Airbag
  - Read/Write complete EEPROM of airbag control units Siemens (CAN bus - ISO15765). Audi A6/Q7/Allroad, VW Golf5..., Skoda Octavia II ..., Seat Altea ...
  - With this special function you can Read/Write EEPROM memory of the airbag module
  - Clear the crash data of the airbag module
• Custom Read/Write
  - Using this application you can read/program memory in some electronic control unit
• PIN Convertor
• Service interval
  - Using this function you can perform reset of the service reminder, reset of the service interval parameters or change service interval options
  - Service intervals reset for the models with UDS diagnostics
• Remote control adaptation
  - Using this application, you can learn remote controls
• Navigation
  - Using this application, you can enable/disable the “Eject” button of the “Navigation” system
• Cruise control system
  - Using this application, you can activate/deactivate a cruise control system and change the related
  steering wheel electronics( SWE) configuration if SWE unit is available
• Brake pads change
  - Using this application, you can “Open rear parking brake for pad change”, “Close rear parking
  brake”, perform “Parking brake function test”
  
  
  
  Prices of the special fucntions:
  
  
  AN008 - Read/Write flash/counters ECU - free
  AN011 - TV Activation - free
  AN012-A - EDC16x - Odometer by OBDII - 300 euro (250 euro without included VAT)
  AN015 - FLASH Memory ECU - free
  AN022 - Micronas programmer - 300 euro (250 euro without included VAT)
  AN023 - VW Crafter key programming - 300 euro ( 250 euro without included VAT)
  AN025 - EDC16/MED9/SIMOS PPD - PIN, Eeprom - 900 euro (750 euro without included VAT)
  AN027 - Dealer key for Audi Q7,A6,Allroad(2004-2010) with existing key - 600 euro (500 euro without included VAT)*
  AN028 - Odometer by CAN - 420 euro (350 euro without included VAT)
  AN029 - IMMO data immobilizer/ECU - 498 euro (415 euro without included VAT)
  AN030 - Key Adaptation (All VAG models) - 600 euro (500 euro without included VAT)
  AN031 - Dealer key preparation including Golf 6, Audi Q7, A6, Allroad - 996 euro (830 euro without included VAT)
  AN032 - Read sec. access CAN - 300 euro (250 euro without included VAT)
  AN033 - Read/Write EEPROM ECU - 348 euro (290 euro without included VAT)
  AN034 - Odometer/PIN by K-line - 300 euro (250 euro without included VAT)
  AN036 - Airbag (K-line, CAN) - 498 euro (415 euro without included VAT)**
  AN037 - ECU adaptation by OBDII - 960 euro ( 800 euro without included VAT)
  AN038 - BCM2 - Audi A4/A5/Q5 2007+ key programming - 498 euro ( 415 euro without included VAT)***
  AN039 - BCM2 key programming by OBDII - 2400 euro ( 2000 euro without included VAT)****
  AN040 - Component protection manager (generation 1/2) - 2400 euro ( 2000 euro without included VAT)4*
  AN041 - EDC17/MED17 PIN/CS/MAC read by OBDII - 1200 euro (1000 euro without included VAT)5*
  AN042 - Read/Write EDC17/MED17 Flash/EEPROM through boot-mode - 480 euro (400 euro without included VAT)
  ZN001 - TAG programmer - Transponder Programmer - 600 euro (500 euro without included VAT)
  
  VAG Odometer package - include (AN012-A,28,33,34) - 1200 euro (1000 euro without included VAT)
  VAG Dealer key package - include (AN23,25,27,29,30,31,32,33,34,39,41 + TAG programmer) - 6780 euro (5650 euro without included VAT)
  VAG Package 1 - include (AN012-A,23,25,27,28,29,30,31,32,33,34,39,41 + TAG programmer) - 7320 euro (6100 euro without included VAT)
  VAG Package 2 - include ( AN012-A,23,25,27,28,29,30,31,32,33,34,36,39,40,41 + TAG programmer) - 9480 euro (7900 euro without included VAT)
  VAG Package 3 - include (AN012-A,23,25,27,28,29,30,31,32,33,34,36,37,39,40,41,42 +TAG programmer) - 10560 euro (8800 euro without included VAT)
  
  
  Note: Ordering of special functions is possible only if you have our diagnostic interface AVDI
  * Need from a working key and Special Function AN030
  ** All customers who have the old function AN010 can buy AN036 for 315 Euro (without VAT)
  *** To make a key you need to read the BCM2 dump. This is possible either by OBDII (if car is with 8K0907298C BCM and has working key) or with the ABPROG(ZN030) with BCM2 adapter
  **** To use this feature you must have also enabled functions: AN030 + AN031. This function covers the functionality of AN038, so that new customers do not need to buy AN038. Customers who already have activated AN038 can make updates to AN039 for 1585 Euro (without VAT), also they have to activate functions AN030 and AN031.
  4* All customers who have the old function AN035 will receive AN040 FREE of charge
  5* All customers who have the old function AN014 will receive AN041 FREE of charge

->Prices for packages

MAIN SCREEN

<< PRODUCTS >>